Instrument Acoustics

Soundboards & Vibrations

Instrument Acoustics

Soundboards & Vibrations

Instrument Acoustics

Soundboards & Vibrations

Soundboards & Vibrations

How a plate responds to an impact, how its modes become visible, and how those observations change during construction.

Tap-tone testing

A gentle impact excites a freely supported part or an assembled instrument. A microphone records the sound; the waveform and frequency spectrum reveal the decay and prominent frequency components. This is an acoustic recording, not a force-normalized frequency-response function.

Record dimensions, mass, thickness and grain direction. Keep the support, impact position and microphone distance and direction consistent. Avoid a second bounce and clipped recordings; allow each response to decay before the next impact. Save the original recording and its analysis settings.

Inspect the time signal before selecting the response for frequency analysis. Changes in impact force, support and analysis window can change the spectrum. Peak heights from separate uncalibrated taps should not be treated as a direct comparison of acoustic output.

Chladni patterns

A sinusoidal source excites the plate while light particles collect around regions of low motion. In the procedure described in my chapter, the plate rests on soft supports and is driven with a loudspeaker. Adjust the excitation frequency, observe the pattern, then check the supports and repeat the observation.

Record both the frequency and the pattern. Support placement and neighbouring modes affect the result; the particle pattern is not a complete measurement of vibration amplitude or phase.

Force and response

Frequency-response measurements use a measured force input and a response such as acceleration or sound pressure. Defined positions, directions, boundary conditions and calibration allow the relationship between input and response to be examined. A microphone spectrum alone does not provide the same information.

Soundboard studies & observations

Sense and Science — TapTone & FFT & Chladni Figures
Sense and Science — TapTone & FFT & Chladni Figures

Originally shared 2025-10-10

Tap Tone, FFT and Chladni Figures

I use spectra and Chladni patterns alongside flexing, tapping, and listening to soundboards. These measurements help document the properties explored through hands-on adjustments.

From the journal
From the journal

Originally shared 2025-07-20

Vibration Modes of the Oud

Examples of the oud’s vibration modes and their relationship to loudness and timbre. Chladni testing is one method of observing these patterns in the workshop.

From the journal
From the journal

Originally shared 2024-02-22

Testing a Bluetooth System for Chladni Analysis

A trial of whether a Bluetooth system enclosed in a sound box can provide the excitation needed for Chladni analysis.

From the journal
From the journal

Originally shared 2024-02-05

Resonance and Vibration Modes

Studying resonance and vibration modes in stringed instruments, including the oud, and their relationship to tonal character.

From the journal
From the journal

Originally shared 2024-01-06

Chladni Patterns on an Oud Soundboard

Observing Chladni patterns on an oud soundboard to explore its vibration characteristics.

From the journal
From the journal

Originally shared 2023-12-29

Soundboard Adjustment with Chladni Patterns

Using Chladni patterns to guide soundboard adjustments, including the contour of the plate and the geometry and height of its braces.

From the journal
From the journal

Originally shared 2023-12-21

A Chladni Plate for Teaching

A new Chladni plate added to the teaching materials in our conservatory laboratory.

Chladni figures.. percussion instrument, bendir
Chladni figures.. percussion instrument, bendir

Originally shared 2023-05-26

Chladni Figures on a Bendir

Observing Chladni figures on a bendir.

From the journal
From the journal

Originally shared 2022-12-15

Chladni Analysis of a Bendir

A Chladni figure used to explore how a bendir vibrates and produces sound.

From the journal
From the journal

Originally shared 2022-11-15

Vibration Modes and Soundboard Thickness

Using a vibration mode as a guide when assessing oud soundboard thickness, alongside the wood’s density and stiffness.

One of the Chladni figures of the wood plate
One of the Chladni figures of the wood plate

Originally shared 2022-04-20

Chladni Figure of a Wood Plate

A Chladni figure showing a vibration mode of a wood plate.

Investigating a bağlama soundboard — source film still
Investigating a bağlama soundboard — source film still

Originally shared 2021-03-23

Investigating a bağlama soundboard

Vibration and acoustic analysis of a bağlama with a Nomex-laminated double-top soundboard, made by Süleyman Guitars.

Vibration modes and bridge position — source film still
Vibration modes and bridge position — source film still

Originally shared 2021-02-28

Vibration modes and bridge position

Exploring vibration modes and the position of the bridge in relation to the sound of the bağlama.

From vibration to sound — source film still
From vibration to sound — source film still

Originally shared 2020-04-30

From vibration to sound

Observing sound formation in a simplified model of a vibrating string and soundboard.

From the journal — source film still
From the journal — source film still

Originally shared 2019-09-05

Chladni Patterns in Instrument Making

Using Chladni patterns during instrument making and when investigating acoustic problems in completed instruments.